Great quality, great time saver!

Installed on 2018 Rally along with Flasher Relay and License Plate Light. Tutorial videos made it a snap. Took about 45 minutes start to finish for me. Had previously broken left rear turn signal on two occasions and Honda likes to make money on parts.

Advantages: Clean lines. Bright.

Disadvantages: None that I can think of unless the DOT approval thing is a hassle.

Installed the clear version on my 2020 full black ZH2; love it.

With the relay to slow the flash rate, the fender eliminator, and license plate light, the end result is gorgeous. I was a little apprehensive about tapping into the oem wiring for the plate light, but those little red tab "things" are super easy to use.

Install was a breeze, fits nice a snug it's place, and really cleans up the look.

A good friend came over to check it out, he drives a 2018 R1M with an integrated tail light as well. When I showed him the light, and the different signal flash modes, he was a little bit on the jealous side; which made me even more happy ;)

Advantages: Easy install with gorgeous end result, especially when coupled with the fender eliminator. As previously mentioned, the z900 fender eliminator works with the 2020 ZH2

Disadvantages: None..

We have two CRF250L's. Both bikes got the following: Integrated Tail Light/Fender Eliminators, LED Front Pod Turn Signal Bundle ARO18 clear for one, LED Front Pod Turn Signal Bundle BL6 smoked for the other, and LED Low-Profile Universal Fit License Plate Lights for each.

Advantages: Man, they look great. That rear fender is so ugly. We opted for the hyper flash because we thought it might be easier to see and get the attention of other motorists. They look awesome and were easy to install.

Disadvantages: No disadvantages at all.

needed relay for a '99 ZX7R contacted tech support and Mark answered with 2 pics. of the original relay he found that this one should work, and it did.

Advantages: you can go full LED and set the flash rate to your liking.

Disadvantages: none does what is intended to do.

I love these. After looking at all of the aftermarket signals for my bike, TST has the best ones by far. They sit perfectly flush, the halo really adds to the look of my bike with the smoked lens, and they are pretty bright. Install was easy peezy with the step by step video. I'm very happy with my purchase!

Advantages: Bright
Easy install
Sits perfectly flush
Smoked lens look amazing

Easy to install, comes with all the parts and is easy to program. It comes with balance resisters that are bulky and have a ceramic coating, but I would order the TST relay.

Advantages: Fast install, very direct, and simple to setup.

Disadvantages: No instructions on install, your going to have to look up the YouTube video although it's not hard to figure out.

Bought these to replace the OEM's on my FZ-10. I liked being able to buy a complete plug and play kit, and the install video on Youtube was invaluable. They look much better than stock, and do not stick out nearly as far. Fit and finish or parts is great, definitely worth the price. Thanks TST.

Advantages: Plug and Play, just provide your own electrical tape. No modifications necessary to install on your FZ-10. Look much better than the OEM lights.

Disadvantages: Not DOT certified, but that was made clear by TST before I made the purchase.

This worked perfectly out of the box. No more mess of wires with load changers. I cheated during install and only took the two screws out from the main side panel, then just popped the front end of the panel off and changed the relay without fully removing the panel. It was easy and saved some time. Thanks TST for another great product!

Advantages: Easy install and any combination of LED blinkers now fully functions with no further modifications to the electrical system.

Disadvantages: None! And the price is more than reasonable for a quality component like this.

Very pleased with my purchase, fast shipping as well. Ordered on friday amd delivered on monday (Kansas city). Ordered the smoked lens, license plate light, elite 1 eliminator and gen 2 flasher relay. All parts installed in about 2 hours. The informational videos really helped out. My only small gripe is the hole in the beautifully made close out would still let water in after routing the plate wire through it. Maybe a rubber grommet could fix that? I ended up putting a dab of clear silicone to seal it off. Other than that I am very happy. As always TST Industries has done a great job, thanks for the hard work.