I acknowledge that the product(s) being purchased () was/were designed and intended for closed course competition use only. The product(s) is/are neither designed nor intended for use on public roads or land and is against Federal and State regulations to do so. By proceeding with this purchase, I , agree to only use the product(s) for closed course competition.
All new TST Industries 2006-2007 Honda CBR1000RR Halo-1 Flushmount Turn Signals with a glowing halo.
Important note: these Halo-1 units are designed to be a perfect match for the 2007-2012 CBR600RR mid fairing, and we found they work quite well for 06-07 1000RR which is why they are offered here. That said, there is a small gap between the lens and fairing after installation. We believe for most people this will be a non-issue, but want to ensure awareness prior to your purchase. You can see the end of our installation video for a clear demonstration of how these fit on a North American 06-07 1000RR.
Applications: Honda CBR1000RR 2006, 2007
Features
DescriptionThe Honda CBR 1000RR Halo-1 technology is an exciting innovation by TST Industries. With the most advanced optics in the flushmount signal market and true plug-and-play installation*, this system is sure to be a hit. The running light function of these signals has a glowing halo (patent pending) in a color of your choice. During signaling, the Halo element turns off to eliminate color bleed*. The signaling circuit packs three 1W amber LED chips that fire a super bright signal through a lens packed with light dispersing hexagonal dome optical elements. As a result, you have a very bright and noticeable signal lamp that can be easily seen from the front and side. The installation takes just minutes. All that is required is plugging the signal into the harness*, pushing it into the fairing well, and fastening it down with the provided nut and washer. *INTERNATIONAL BUYERS: The plug-and-play installation has been confirmed on American models where the OEM plug has three conductors. If you are ordering from outside of South and North America, please check your signal plugs first. In case your plug has only two conductors, please follow the instructions found in our FAQ tab for installation. Please note this item is not DOT approved and may not comply with the laws and regulations in your area. See our Terms & Conditions for more information. Installation
Q: Do these signals require any wiring or splicing?
A: No - these signals are completely plug and play. Q: The signals have a 3 pin connector but my signals only have 2. How do I install? A: Some bikes outside of North America will only have 2 pins. For bikes with a two pin signal plug you would take the pins out of the three conductor plug on the halo-1 signals. The wires in our plug have crimped on metal connectors. You will insert the halo-1 black wire crimp into your plug position that has the green wire. Then the halo-1 red wire crimp will go into the remaining slot on your bike's plug. Use electrical tape around the plug with the pins in it and make a nice tight electrical tape junction. You will be left with the green wire from the halo-1 signals. If you leave it disconnected you will not have the running light. At this point you can run a wire from the positive lead on your low beam headlight to each of the green wires on the halo-1's. This will give you running lights when the bike is on, and they will shut off with the bike. You can also opt to run a wire to the positive terminal on the battery and use a fuse and a switch on that connection. The fuse should be immediately next to the battery, and the switch should be accessible somewhere for you so you can switch the halo-1 running light on and off at your will. Q: Do these signals have running lights? A: Yes! In a variety of color choices. Q: Do I need a flasher relay? A: Installing aftermarket LED lights may cause your signals to flash faster than the OEM speed. Purchasing one of our LED flasher relays will correct this problem. Q: How long will it take for me to receive this once I order it? A: Our handling time is 1-2 business days, and the shipping time varies based on the shipping method selected. To learn more about shipping times, please see the articles in our Terms & Conditions regarding domestic and international shipping here. Q: I'm located outside of the United States. Will I have to pay duties on this item? A: Some countries charge additional fees when a package is imported and delivered to the recipient. We have no way of knowing or estimating what these fees will be. It is the buyer's responsibility to cover these additional costs. Q: What is your return and warranty policy? A: Please read over our policies thoroughly on our terms and conditions page BEFORE making your purchase. TST Industries Terms and Conditions |
WARNING: Cancer and Reproductive Harm - www.p65warnings.ca.gov