This would be a 5* review if not for one thing. Ease of installation is great however they recommend Threadlock on the blockoff plate they they/you do not supply. Vibra-tite VC-3 is not readily available in most, almost ALL stores and unless you watch the install videos prior to purchase you will not know you would need this, and as such would make sense to add a 5oz tube as part of the provided kit. I drove all over las vegas looking for a tube of this, you offer no alternative solutions other than don't use Threadlock blue as you will melt the plastic. So currently my bike in in pieces unable to ride for 2 days waiting on an amazon delivery.

Advantages: Will look great on the R7 especially with the addition of the newly released turn signals specific to this bike

Disadvantages: A recommended sealant to be used is not offered in the kit and is not in most stores. Make sure you find this specific threadmate prior to purchase in order to save rework time

Eventually got’em after 4 months of waitin. Easy worldwide shipment to my doorstep.

Changed the look of my bike 180*
Luv’em. It took me less an hour to assemble it. Thx TST team

Advantages: Ordered and shipped worldwide, received in 10 days

Disadvantages: NA

5X brighter than OEM. Running light provides added visibility and looks great compared to original equipment.

Will these turn signals replace the rear signals? Red halo running light would be nice for rear turn signals. I did purchase the tst tail eliminator kit with the OEM turn signal bracket.

This is the 2nd taillight I've installed on my 2013 ZX6R. Let me tell you, this light blows its competitors out of the water. It was very easy to install as well as to program how you wanted the light to work.

The only real complaint I could say about the taillight is, the hole on top that lines up with the upper part of our rear fairing plate could be tighter. Have a little slop in the top portion of the light but not enough to cry about.

Advantages: Very bright brake light. Can program it to flash for a couple seconds with initial press of the brake. Very easy to install

Disadvantages: None yet

I received this kit in a few days from ordering and it was well packaged. Did not take long to install. Looks really good.

Fit was outstanding and installation was super easy! Even comes with the closeout plates, which i wasn't expecting!

Awesome! I have several TST accessories now for my R3 and the quality and support has been great. The installation videos are top notch. Thanks!

I’m giving only four stars because I shop on TST industries quite a lot and I like their products it’s a local business

Advantages: Strong nicely made

Disadvantages: Purchased Red color. Once arrived it’s more like a orange color just not as bright. Def. not deep red.

The general weight and finish of the product is good. The threads are clean and there are no unfinished edges/burrs all around. The slider pucks fit great. The color is off, and they are an eye sore next to my other anodized red parts...sorry, not sorry. If TST offered to ship me black replacements as a good will gesture, I would not turn them down. Please reach out and you have a customer for life.

Advantages: They threaded in without issue; Install is very simple; The slider puck should save the bar ends in a minor drop

Disadvantages: The red is, in reality, a shade of orange. We need to be honest about that, simply put. Your "important note on color" is just lazy. Work with the manufacturer to be better. To say this is a problem with all anodized parts is simply passing the buck. I have cheap-ish Chinese levers that are truly red, and after two years have not faded as one may worry about. Hold your vendor/manufacturer to a higher standard. For this reason I have to give only 3 stars, as a main selling point of this type of product is the aesthetic. I wish I could attach a picture, as I am not being sensational about this.

A straight forward install that doesn’t take too long at all either. The only thing that had me scratching me head was the license plate mount and the lack of room between the signal light threads and the bolt threads that hold the bracket in place. There’s really not a lot of room to work as the lights and mounting bolt damn near touch. Since the kit I got came with 6 washers I ended up doubling up the washers on the front of the license plate (basically made them spacers) to push to bolt further outward to give me more room behind the plate where the signal light comes through. One washer and the nut on the backside and it fit snuggly and didn’t feel like a ‘jerry rig’. The included Signal Plug Adapters allow this project to truly be a plug and play install. The Smoke BL6 lights I got are pretty slick looking and super bright. Like, my god those are bright signal lights, bright. The bright amber LED’s definitely set themselves apart from the red glow of your running/brake light.

Advantages: Super bright LED’s make no mistake your intention to turn.
Easy plug and play installation makes me feel like I know what I’m doing for once.


Disadvantages: -The license plate bracket can be a little tricky when you’re trying to tighten down the nut on the signal light and trying to keep it straight, even and flat. It’s easy to have one light lined up perfectly and the other looking a bit more up or down, like an iguana’s eye balls.
-Can’t be used in conjunction with the TST Programable and Sequential Tail Light AND utilizing its signal light function. You can still use that same tail light for running/brake lights, but you sacrifice utilizing the tail lights signal function. No way to split and splice to use both tail light signals and a separate set of signals.